Sintra - Novo plástico PVC
Sintra - Novo plástico PVC
Surgiu este novo material, que tem cerca de metade do peso do pvc convencional e que pode ser agrafado, pregado, colado (incluindo ciano).
A maioria dos modelistas que conheço fazerem modelos Chris Craft estão a gostar de trabalhar com este material nesses modelos.
A minha pregunta é :
Alguem sabe onde se pode comprar este material em Portugal ?
http://tri-dee.com/sintra_plastic_pvc.htm
A maioria dos modelistas que conheço fazerem modelos Chris Craft estão a gostar de trabalhar com este material nesses modelos.
A minha pregunta é :
Alguem sabe onde se pode comprar este material em Portugal ?
http://tri-dee.com/sintra_plastic_pvc.htm
-
- Almirante
- Mensagens: 3828
- Registado: domingo out 09, 2005 11:41 pm
- Localidade: Cascais
- Contacto:
- Helderluiss
- Almirante
- Mensagens: 3053
- Registado: sexta nov 18, 2005 1:00 pm
- Localidade: Palmela
- Localização: Palmela
- Contacto:
- Helderluiss
- Almirante
- Mensagens: 3053
- Registado: sexta nov 18, 2005 1:00 pm
- Localidade: Palmela
- Localização: Palmela
- Contacto:
-
- 1º Tenente
- Mensagens: 196
- Registado: terça ago 08, 2006 4:07 pm
-
- Capitão de Mar-e-Guerra
- Mensagens: 611
- Registado: terça nov 07, 2006 1:18 am
- Localização: Polima-S.Dos. de Rana
- Helderluiss
- Almirante
- Mensagens: 3053
- Registado: sexta nov 18, 2005 1:00 pm
- Localidade: Palmela
- Localização: Palmela
- Contacto:
Num outro forum li algo interessante acerca deste plastico.
A empresa americana Fx Models dedicada a maquetes para filmes e alguns modelos rc viu grande parte das ferramentas da sua oficina em aço enferrujarem devido ao acido libertado deste plastico quando desbastado e/ou queimado.
Se no aço a coisa fica neste estado mais vale prevenir e provavelmente o uso de uma boa mascara não seja despropositada.
A mensagem original é a seguinte:
"Notes on Sintra... I have been using it for about 2 years and I can tell you some things about it that you dont know perhaps. This will be illuminating to others as well. Sintra's chemical makeup is such that if you sand it or burn it, [ie heat it up] it will give off an acid. This acid is not an immediate searing acid but what it does is to linger in the air, and proceed to attack ALL steel items in your workshop. In our case, we worked with Sintra in 1mm, 2mm and 3mm thicknesses and within two weeks EVERY piece of steel in the shop rusted, from steel Allen head screws, to the floor mount post on one of the drill presses. Even steel rulers were not exempt so I suggest that you work carefully with Sintra. The recovery and replacement of items was very costly so just a word of warning...
I now hate Sintra and its now shop policy to refuse any job that brings it as a requirement... "
A empresa americana Fx Models dedicada a maquetes para filmes e alguns modelos rc viu grande parte das ferramentas da sua oficina em aço enferrujarem devido ao acido libertado deste plastico quando desbastado e/ou queimado.
Se no aço a coisa fica neste estado mais vale prevenir e provavelmente o uso de uma boa mascara não seja despropositada.
A mensagem original é a seguinte:
"Notes on Sintra... I have been using it for about 2 years and I can tell you some things about it that you dont know perhaps. This will be illuminating to others as well. Sintra's chemical makeup is such that if you sand it or burn it, [ie heat it up] it will give off an acid. This acid is not an immediate searing acid but what it does is to linger in the air, and proceed to attack ALL steel items in your workshop. In our case, we worked with Sintra in 1mm, 2mm and 3mm thicknesses and within two weeks EVERY piece of steel in the shop rusted, from steel Allen head screws, to the floor mount post on one of the drill presses. Even steel rulers were not exempt so I suggest that you work carefully with Sintra. The recovery and replacement of items was very costly so just a word of warning...
I now hate Sintra and its now shop policy to refuse any job that brings it as a requirement... "